tag:blogger.com,1999:blog-3479039295802526856.post2090042523207078472..comments2023-10-30T01:09:04.693-07:00Comments on MinuteEngineering: Control car with arduino and labview12http://www.blogger.com/profile/07441742525398566732noreply@blogger.comBlogger13125tag:blogger.com,1999:blog-3479039295802526856.post-63836222330612574422014-08-28T05:57:25.184-07:002014-08-28T05:57:25.184-07:00hi >> i want to controll my car by wireless ...hi >> i want to controll my car by wireless rather than wire pleas help me Anonymoushttps://www.blogger.com/profile/06370677793655645497noreply@blogger.comtag:blogger.com,1999:blog-3479039295802526856.post-63451035554222436192014-08-28T05:54:27.754-07:002014-08-28T05:54:27.754-07:00hi >>> i want to controll my car using wi...hi >>> i want to controll my car using wireless rather than wire pleas help meAnonymoushttps://www.blogger.com/profile/06370677793655645497noreply@blogger.comtag:blogger.com,1999:blog-3479039295802526856.post-60487868569037214172013-08-20T11:36:35.168-07:002013-08-20T11:36:35.168-07:00you have to just upload a single code only for one...you have to just upload a single code only for one time then the whole programming is done with LabVIEW if you don't know the procedure of interfacing of arduino and LabVIEW then visit my previous posts and follow step by step guide.12https://www.blogger.com/profile/07441742525398566732noreply@blogger.comtag:blogger.com,1999:blog-3479039295802526856.post-33929707635079784802013-08-19T21:52:04.976-07:002013-08-19T21:52:04.976-07:00what are the codes used in the arduino? what are the codes used in the arduino? Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-3479039295802526856.post-84049714124201983512013-04-28T20:12:02.972-07:002013-04-28T20:12:02.972-07:00i cant run the program because the sub.vi or the d...i cant run the program because the sub.vi or the digital write pin.vi is missing also the close.viAnonymoushttps://www.blogger.com/profile/05194656046949737186noreply@blogger.comtag:blogger.com,1999:blog-3479039295802526856.post-53029941314494861852012-08-01T18:26:35.911-07:002012-08-01T18:26:35.911-07:00Congrates i am not using any batteries but providi...Congrates i am not using any batteries but providing voltage from arduino to controller.12https://www.blogger.com/profile/07441742525398566732noreply@blogger.comtag:blogger.com,1999:blog-3479039295802526856.post-47219181300511950672012-08-01T09:51:42.778-07:002012-08-01T09:51:42.778-07:00I got it to work. There should be no batteries in ...I got it to work. There should be no batteries in the controller when attached to the arduinoJacksonnoreply@blogger.comtag:blogger.com,1999:blog-3479039295802526856.post-34194179766848134162012-08-01T06:25:17.640-07:002012-08-01T06:25:17.640-07:00I installed the arduino library and NI-VISA packag...I installed the arduino library and NI-VISA package and the arduino software and set up the arduino. When I ran the program, the wheels of the car would spin as soon as I started the program, but it would not respond to pressing any of the switches. A short time after that one of the batteries in the controller exploded and started leaking on the table. I am trying to figure out where I went wrong and I think it is with the wiring. I have soldered wires onto the 4 areas for control as you did and onto V+ and V- as well. I put the V+ wire into the Vin pin and the V- wire into the ground pin on the arduino. The other 4 wires for control I put in pins 3, 4, 6, and 8. I am unsure what I did wrong and any advice would be helpful. Thanks a bunchJacksonnoreply@blogger.comtag:blogger.com,1999:blog-3479039295802526856.post-65020157888500382862012-08-01T03:10:53.270-07:002012-08-01T03:10:53.270-07:00welcome Jackson , i am using labview 2010 and i th...welcome Jackson , i am using labview 2010 and i think arduino library is compitable with 2011 but i used 2011 runtime that makes 2010 compitable to 2011 if you are using 2010 version than you must look at my previous post there is complete steps are written how to download, instal arduino library.12https://www.blogger.com/profile/07441742525398566732noreply@blogger.comtag:blogger.com,1999:blog-3479039295802526856.post-57606987124256179902012-07-31T09:08:13.323-07:002012-07-31T09:08:13.323-07:00I noticed from your video that you have a wire con...I noticed from your video that you have a wire connected to Vin on the arduino. Do you have batteries in the controller or are you using the arduino to power the controller?Jacksonnoreply@blogger.comtag:blogger.com,1999:blog-3479039295802526856.post-58258765060817658972012-07-31T07:31:23.360-07:002012-07-31T07:31:23.360-07:00My labview is an older version than yours and I ca...My labview is an older version than yours and I cannot open your VI. Is there a possiblity that you could save it as a 2009 version of the VI? I saw online you can save the vi as an older version and I was wondering if you could possibly do that.Jacksonnoreply@blogger.comtag:blogger.com,1999:blog-3479039295802526856.post-70924879622823198132012-07-31T06:53:56.737-07:002012-07-31T06:53:56.737-07:00I am doing a similar project and I am wondering wh...I am doing a similar project and I am wondering what pins you used on the arduino board?Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-3479039295802526856.post-45464074913198422772012-07-20T06:37:58.626-07:002012-07-20T06:37:58.626-07:00i really apreciate u for doing a great job... prou...i really apreciate u for doing a great job... proud on u my PartnerAnonymoushttps://www.blogger.com/profile/10633944077677732441noreply@blogger.com